A top-loader washing machine with a shock absorber makes sure that the machine remains stable during the spin cycle. But the shakes problem of your washing machine arises when the shock absorber gets damaged or unable to function properly.
At that time, you are going to see the washing machine shakes problem in your washer. More on this topic is discussed down below.
What makes a top load washing machine shake?
A top load washer is prone to movements caused by the spinning of the drum and the action of its suspension system. The suspension system is made of hoses and springs that are designed to evenly distribute the load of the machine over a fixed area. These parts might become loose or worn and cause the washing machine to shake and move excessively.
One of the most common reasons a top-load washing machine shakes is because the machine’s leveling feet are not set correctly. This causes the machine to rock back and forth and vibrate. If your machine is rocking, you can fix the problem by resetting the leveling feet using a screwdriver.
Also, Washer shaking can be caused by a broken belt, worn bearings, or a loose pulley. It can also be caused by overloading the machine.
Is it normal for washing machine to shake during spin cycle?
Yes. When the washing machine is shaking during the spin cycle, the washing machine is performing abysmally. Just like when a car shakes violently when it reaches a speed of 70 miles an hour, the washing machine will shake violently when it reaches a speed of 220 rotations per minute.
Why Top load washer shakes excessively during the spin cycle?
This happens mainly because of the fast spin rate that causes the top load washer to vibrate. It is recommended that you use a lower spin cycle.
If you load over to Top load washing machines then it vibrates when it spinning. Because the weight of the drum and the water working together against the frame of the washing machine.
Learn about some parts of top load washer releted to shaking and vibration
Suspension rod and spring
The suspension rod and spring guide the tub up and down when the load is dumped and loaded.
First, you need to disassemble the top of the washer using the hex wrench provided in the replacement parts package. You will see the washer and suspension rod and spring. Remove the spring and using the hex wrench as a lever, remove the suspension rod
The rod and spring that hold the drum of your washing machine up are called suspension rods. If these are broken, the tub with drum of the washing machine will sag. The rods can break suddenly, or you may be able to tell that they are coming apart if the lid sags and the machine makes loud noises when it is running. To replace the suspension rod, you need to carefully remove the lid from the washing machine. The lid is usually held on with screws. You need to remove the washer cabinet too. After that, the suspension rod will simply pull out. You can replace it with a new one that is a little bit longer than the old one. This will make sure that the rod is strong enough to hold the drum up.
Snubber Ring
Snubber rings keep the washer from bouncing when it shifts from horizontal to vertical, and dampers keep the spinners from getting too much of a kick (as the drum rotates). Snubber rings are only required when a washer is used in a way in which the clothes are not pressing against the bottom of the drum at the end of the wash cycle, such as during the spin cycle.
Hoe to replace Suspension springs, snubber ring and drive belt?
Feet or Leveling Leg
Many top-load washers feature an adjustable leg level so you can easily raise or lower the washer to create a horizontal or vertical line of water when the door is closed. Most modern washer models also offer an adjustable pedestal level, which allows you to adjust a part of the door frame.
How to know your washing machine shock absorber is damaged?
First, you should cut off all the power sources for your washing machine. Different models are used to place their shock absorbers in different locations inside the washing machine. You just need to know your model and check out their official sites to know where the shakes remover is placed in your washing machine.
Besides, you can also go throw the manual guideline that comes with your washing machine.
Broken shock observers of your top-loading washing machine can create leakage problems on the washing machine. You also need to look for the broken attachments and shock absorbers parts. If you find any of these problems in your washing machine, then you need to fix this issue to get rid of this top-loading washing machine shakes problem.
How to fix the top-loading washing machine shakes problem?
To reduce your washing machine from shaking, you should check the leveling of the machine. If this is not the case, you may tighten the nuts that hold the legs of your washing machine.
- Remove foreign objects in the tub if president.
- Check the drive belt for damage and replace it if damage
- Clean and lubricate the idler pulley and the motor pulley.
- Check for loose parts if you find any parts loosen then tight the parts by screw drivers or hex wrench.
- Check the screws that hold the idler pulley and tight if needed.
- Check the tub bearings broken or damage. Replace it after removing damage one. use pully puller to remove bearing.
- Put the machine on a more solid and Sturdy surface
- Make sure the machine’s load is balanced and not over. If over loaded Reduce the load size of the machine by removing excess items. Than balance the load by placing heavier items at the bottom
- Clean the rubber coupling at the base of the agitator
- Raise the agitator to its highest position
- Tightening the agitator bolts if loosen
- To stop the top load washer from vibrating, you need to add air to the clothes in the machine. You can do this by placing a few tennis balls in the machine with the clothes.
- You can Purchase Washing Machine anti Vibration Pads
- Contact the manufacturer for other suggestions
Sometimes uneven cloth piles can also be the reason for your washer shaking. You just need to remove some clothes and restart the washing machine to fix the problem. Make sure your washing machine is level to the ground. If you face a shaking problem with a new washing machine, then you need to look for the shipping bolts.
You just need to unscrew them if that is the case for your top-loading washing machine shaking. Running an empty cycle can be very helpful to figure out what is causing the shaking problem in your washing machine.
If you find it hard to get one perfect for your washing machine, then it is best to contact the manufacturers of your washing machine. Attaching the new washing machine shock absorbers is not that hard, and anyone with knowledge of washing machine parts can do it. Besides, you can also hire professionals to get your work done.